Plating Shop Baskets and Work Bars Design and Fabrication PlatingShopBasketsandWorkBarsDesignandFabrication_SourcesSought

THIS IS A REQUEST FOR INFORMATION (RFI) ONLY - This RFI is issued solely for information and planning purposes - it does not constitute a Request for Proposal (RFP) or a promise to issue an RFP in the future. Responses will be treated as information only and will not be used as a proposal. Solicitations are not available at this time. Any requests for a solicitation will not receive a response. This notice does not constitute a commitment by the United States Government to contract for any supply or service whatsoever. The Army Contracting Command (ACC) - Aberdeen Proving Ground (ACC-APG), Tobyhanna Division, is conducting this RFI in order to identify potential vendors that possess the capabilities to support the design and fabrication of lifting baskets and work bars. The quantity of the baskets and bars listed below: TYAD s quantity of baskets and work bars: 6ea - 8 foot baskets 1ea Different variety of 8 foot basket 2ea - 4 foot baskets 6ea - 12 foot work bars 8ea - 8 foot work bars Please refer to Objective below and attached DRAFT Performance Work Statement (PWS) for complete details. Objectives: The contractor shall provide all necessary services as defined in the DRAFT PWS. This specification includes details for the design and fabrication of the new baskets and work bars. Used or remanufactured equipment is NOT acceptable. The contractor may use TYAD s current supply of baskets and work bars as a outline for their design. TYAD possess technical drawings of the current equipment that the contractor may reference. 2. Application Lifting baskets and the work bars are used in TYAD s plating shop to dip metal into a variety of different liquids like water, acid, and other mixtures. Currently TYAD has baskets and work bars, but they are due to be replaced. The contractor may use the existing baskets and work bars as an outline for their own design. TYAD also has technical drawings of their existing equipment that they will share with interested contractors. The contractor will provide the following services during their design and fabrication. The Contractor will make a visit to TYAD to lay eyes on the equipment, take measurements, and listen to TYAD plating shop employees about desired design changes to the work bars and baskets. The contractor will design new work bars and baskets and include all desired design changes that are feasible and will not compromise the structural integrity of the equipment. The contractor will run stress calculations to determine what the load capacity of the equipment is. The contractor will have one final meeting with TYAD personal to inspect the design. The contractor will fabricate the equipment and TYAD personal will stress test the baskets and work bars as a quality check. Delivery of the fabricated equipment shall be within 6 months of contract award. The equipment furnished under this specification shall be warranted for parts and labor for a period of 1 year from the date of delivery. The government is seeking to award a Firm-Fixed-Price Delivery Order under NAICS code 332510 Hardware Manufacturing. All information submitted in response to this announcement is voluntary; the United States Government will not pay for information requested nor will it compensate any respondent for any cost incurred in developing information provided to the United States Government. All information received in response to this RFI that is marked proprietary will be handled accordingly. Responses to this RFI that indicate that the information therein is proprietary, or represents confidential business information, will be received, and held in confidence. Not responding to this RFI does not preclude participation in any future RFP, if any is issued. Please note, if a solicitation or multiple solicitations are posted in the future, they will be issued by a separate solicitation. The Government reserves the right to follow up on a one-on-one basis with RFI respondents to gain additional information or clarity about information submitted. Interested vendors are requested to provide information of their firm s capabilities to perform the services as noted in the attached DRAFT Performance Work Statement. Please submit any questions regarding this RFI to: Marissa.c.brodi.civ@army.mil Responses to this RFI addressing your company s capability to support this requirement shall be submitted to the above referenced e-mail address NLT Thursday, September 04, 2025 by 10:00 AM EST. Respondents should include the following business information with the RFI response: Company Name and Address; Point of Contact; Telephone Number; E-mail address; Company Cage Code; Primary NAICS; Business Size; Current Registration in SAM; GSA Contract Number:

THIS IS A REQUEST FOR INFORMATION (RFI) ONLY - This RFI is issued solely for information and planning purposes - it does not constitute a Request for Proposal (RFP) or a promise to issue an RFP in the future. Responses will be treated as information only and will not be used as a proposal. Solicitations are not available at this time. Any requests for a solicitation will not receive a response. This notice does not constitute a commitment by the United States Government to contract for any supply or service whatsoever. The Army Contracting Command (ACC) - Aberdeen Proving Ground (ACC-APG), Tobyhanna Division, is conducting this RFI in order to identify potential vendors that possess the capabilities to support the design and fabrication of lifting baskets and work bars. The quantity of the baskets and bars listed below: TYAD s quantity of baskets and work bars: 6ea - 8 foot baskets 1ea Different variety of 8 foot basket 2ea - 4 foot baskets 6ea - 12 foot work bars 8ea - 8 foot work bars Please refer to Objective below and attached DRAFT Performance Work Statement (PWS) for complete details. Objectives: The contractor shall provide all necessary services as defined in the DRAFT PWS. This specification includes details for the design and fabrication of the new baskets and work bars. Used or remanufactured equipment is NOT acceptable. The contractor may use TYAD s current supply of baskets and work bars as a outline for their design. TYAD possess technical drawings of the current equipment that the contractor may reference. 2. Application Lifting baskets and the work bars are used in TYAD s plating shop to dip metal into a variety of different liquids like water, acid, and other mixtures. Currently TYAD has baskets and work bars, but they are due to be replaced. The contractor may use the existing baskets and work bars as an outline for their own design. TYAD also has technical drawings of their existing equipment that they will share with interested contractors. The contractor will provide the following services during their design and fabrication. The Contractor will make a visit to TYAD to lay eyes on the equipment, take measurements, and listen to TYAD plating shop employees about desired design changes to the work bars and baskets. The contractor will design new work bars and baskets and include all desired design changes that are feasible and will not compromise the structural integrity of the equipment. The contractor will run stress calculations to determine what the load capacity of the equipment is. The contractor will have one final meeting with TYAD personal to inspect the design. The contractor will fabricate the equipment and TYAD personal will stress test the baskets and work bars as a quality check. Delivery of the fabricated equipment shall be within 6 months of contract award. The equipment furnished under this specification shall be warranted for parts and labor for a period of 1 year from the date of delivery. The government is seeking to award a Firm-Fixed-Price Delivery Order under NAICS code 332510 Hardware Manufacturing. All information submitted in response to this announcement is voluntary; the United States Government will not pay for information requested nor will it compensate any respondent for any cost incurred in developing information provided to the United States Government. All information received in response to this RFI that is marked proprietary will be handled accordingly. Responses to this RFI that indicate that the information therein is proprietary, or represents confidential business information, will be received, and held in confidence. Not responding to this RFI does not preclude participation in any future RFP, if any is issued. Please note, if a solicitation or multiple solicitations are posted in the future, they will be issued by a separate solicitation. The Government reserves the right to follow up on a one-on-one basis with RFI respondents to gain additional information or clarity about information submitted. Interested vendors are requested to provide information of their firm s capabilities to perform the services as noted in the attached DRAFT Performance Work Statement. Please submit any questions regarding this RFI to: Marissa.c.brodi.civ@army.mil Responses to this RFI addressing your company s capability to support this requirement shall be submitted to the above referenced e-mail address NLT Thursday, September 04, 2025 by 10:00 AM EST. Respondents should include the following business information with the RFI response: Company Name and Address; Point of Contact; Telephone Number; E-mail address; Company Cage Code; Primary NAICS; Business Size; Current Registration in SAM; GSA Contract Number: